Announcement

Collapse
No announcement yet.

L2 wmp12h 300watt floor Monitor

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Arbutt
    replied
    Hi. Yes I did. 54v +/— it's OK I have sorted it now.
    Resoldered the area again. And cleaned it.
    Worked for 4 days 6 hours a day. Been collected to sit about in storage �� till this shit is over


    Mr a

    Leave a comment:


  • The Dude
    replied
    Do you have both rails- +VCC and -VCC?

    Leave a comment:


  • Arbutt
    replied
    Hello again
    Is there anyone that can help or shed some light on this.
    Too me it makes no senses.
    But believe me with a scope probes on input and output both on same setting per div etc.

    Arbutt

    Leave a comment:


  • Arbutt
    replied
    Thank g1.
    OK as follows using dmm on ac range. Between chassis and transistors
    Iq1 base 3v collector 0v emitter 3v
    Iq6 base 0v collector 3v
    Iq10 base 3 .5v collector 0v emitter 3v

    I hope this helps. Many thanks for the help.
    I feared no one would help

    Leave a comment:


  • g1
    replied
    So set it up again so you have 3VAC going in to the power amp.
    Measure the AC voltage at the following points and post your results:
    IQ1 base and collector
    IQ6 b & c
    IQ10 b & c

    Leave a comment:


  • Arbutt
    replied
    Please bare with me struggling to get the map up loaded. I only use a phone. It says I can't upload a pdf format
    Click image for larger version

Name:	IMG_20200220_144842.jpg
Views:	1
Size:	4.26 MB
ID:	856763
    Sorry it's the best I can do at present
    Click image for larger version

Name:	PM12-AMP.jpeg
Views:	1
Size:	469.7 KB
ID:	856764
    Last edited by Arbutt; 02-20-2020, 04:05 PM.

    Leave a comment:


  • Arbutt
    started a topic L2 wmp12h 300watt floor Monitor

    L2 wmp12h 300watt floor Monitor

    Good afternoon to you
    Now I might be being a dick here. But this amp is causing me pain

    It came in to me with a intermittent noise issue.
    I found the fault ir9 was soldered in but leg cut short it wasn't really soldered. Replaced it.
    Out the job went ok
    1 month later it came back distortion after a while.
    I found by heating and freezing the area around iq5 it would go away. In the end I replaced all the transistors in that area iq 1to 7 and 14. As all very close together.
    All changed like for like.
    Tested the amp heat and freezer it all seemed OK.

    Then it went to about 1/2 volume without touching it I wasn't heating or freezing at that time was on for 20 mins before it went
    When I tested it I can see its working perfectly without distortion but low output

    On checking using scope and signal gen I can see the signal in and out of pre amp is OK and higher level leaving the pre amp than the input.
    I'm I being a dick question
    But the signal entering the power amp is at same level as the output.!!!!
    Is this possible?
    Check all voltages 54'v +/- and 15v +/-
    Checked all the transistor /diodes
    Made sure the transistors I changed are good and correct ones
    At output have around 3v ac with gain /vol max
    I'm not an experienced tech. Just play for fun
    Any assistance would be grateful thanks in advance
    Arbutt
    Schematic to follow
antalya escort
pendik escort
sex vidio
porno
antalya escort
beylikduzu eskort bayan eskort bayan escort antalya sirinevler bayan escort
gaziantep escort
Working...
X