Search:

Type: Posts; User: epis; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. Replies
    13
    Views
    1,627

    Tamiya 53176 RC Model Friction Damper Grease...

    Tamiya 53176 RC Model Friction Damper Grease (Hard) | eBay
  2. Thread: Klemt Echolette S

    by epis
    Replies
    143
    Views
    42,988

    Hi guys, when you're talking about HF bias...

    Hi guys, when you're talking about HF bias voltage for recording heads (60 -90 -120volts) do you refer to rms, pk or p-p voltage ?
    Thanks in advance :)
  3. Replies
    29
    Views
    4,617

    yep ;)

    yep ;)
  4. Replies
    23
    Views
    2,932

    You're welcome :) 470 Ohm (as in 5F1) for...

    You're welcome :) 470 Ohm (as in 5F1) for cathode resistor is good starting point, but, most likely you'll have to settle down with 250 Ohm for 6aq5.
    Just measure voltage drop on it , do...
  5. Replies
    29
    Views
    4,617

    Hi yaryaryar, when you increase treble, it's...

    Hi yaryaryar,

    when you increase treble, it's normal to get more hiss, that's thermal noise, you can't really eliminate it. It's not caused by different anode voltages at first preamp tube.
    Simply...
  6. Replies
    23
    Views
    2,932

    Ignore these high voltages you got with...

    Ignore these high voltages you got with calculator. Your load isn't right ( 100k is almost no load).
    If your tape recorder PT was configured to work with 6AQ5, you're good to go.
    I would recommand...
  7. Replies
    0
    Views
    945

    Webcore 2456, 2457 schematic diagram

    Just took it apart, circuit diagram was glued to the bottom of the cabinet.
    35369

    I hope somebody would find it useful.
  8. Replies
    2
    Views
    4,121

    I would say check for proper ground connection on...

    I would say check for proper ground connection on depth pot.
  9. Replies
    30
    Views
    3,497

    Long time ago I was getting magnet wire for...

    Long time ago I was getting magnet wire for pickups from old cars ignition coils ;)
  10. Replies
    30
    Views
    3,497

    Just to share my experience, once I rewound input...

    Just to share my experience, once I rewound input coil of reverb tank, simply I got higher impedance solid state driven tank from old organ and needed low impedance for my tube amp project.
    So I...
  11. Replies
    3
    Views
    1,968

    BJT 100S replaced with MJE13007

    Hi guys,

    I apologize for opening this subject in this subforum, but I didn't know where else to ask for help.
    I'm in the middle of repair of two OttLite desk lamps. Both have same problem, burnt ...
  12. Replies
    3
    Views
    1,493

    Well, it seems I have found a local dealer here...

    Well, it seems I have found a local dealer here in Ottawa :) These guys opened the business a few months ago (I think).
    It should be very convenient for the builders in Canada, considering the...
  13. Replies
    9
    Views
    1,817

    If you meant by separated - isolated ground, you...

    If you meant by separated - isolated ground, you can't without opening transformer (if it's possible) and separate the winding wires from center tap.
    Basically you would get two 18V windings.
  14. Hi Dirk, welcome to forum ! Schematic of your...

    Hi Dirk, welcome to forum !
    Schematic of your amp is similar to Fender princeton 5F2 with added tremolo.
    It looks to me amp was built to accept 6V6 and 6L6 in output. It's hard to say without...
  15. Replies
    3
    Views
    1,493

    Tweed fabric material

    Hi guys,

    recently I built 5E3 deluxe amp. Right now I'm working on cabinet. I would like to cover it in tweed.
    It is hard to get it here in Canada, shipping makes it too expensive to order from...
  16. Replies
    6
    Views
    4,351

    Hi Steve, I like your idea. I'm not gonna...

    Hi Steve,

    I like your idea. I'm not gonna build it, I don't have a need for it now, but it intrigued me,like a puzzle.
    I would use two leveling beams side by side, attached with bolts and...
  17. Replies
    4
    Views
    2,904

    :)

    :)
  18. Replies
    72
    Views
    11,494

    Hi guys, I just wanted to share with you my 40...

    Hi guys,
    I just wanted to share with you my 40 years of experience with soldering.
    First, you need proper tools. Weller stations are the best. Do not try to solder pots casing with cheap 15 to 25w...
  19. Replies
    12
    Views
    3,434

    Excellent!

    Excellent!
  20. Replies
    57
    Views
    8,926

    Hello again, new update : New coil same...

    Hello again, new update :

    New coil same diameter 6", 310 turns, AWG 35, 175 Ohm , NO shield works great, noise reduction looks to me same as in humbucking positions 2 and 4.
    I put switching PS...
  21. Replies
    57
    Views
    8,926

    Hi guys, here is my final impression : Like...

    Hi guys, here is my final impression :

    Like everything in the life, it's about compromises. I have the coil installed in an old Samick, alnico pickups , middle RWRP.
    Coil definitely works, I do...
  22. Replies
    57
    Views
    8,926

    Update I removed partially pickguard from my...

    Update

    I removed partially pickguard from my strat and connected the coil. First coil didn't work,it just added extra noise. It was picking up a lot of noise from my laptop's switching PS....
  23. Replies
    57
    Views
    8,926

    Thanks for your input Ward. I'll try to connect...

    Thanks for your input Ward. I'll try to connect it directly into my strat. I did try reversing the wires, changing relative position of the coil toward pickup and the amp.
  24. Replies
    57
    Views
    8,926

    Sorry guys, this didn't work for me. I made...

    Sorry guys, this didn't work for me. I made second coil, 6" diameter,200 turns, AWG35,122Ohm. I got same result as first time.
    I do understand that additional circuitry could affect efficiency of...
  25. Replies
    57
    Views
    8,926

    Thanks to both of you guys, I'll try with ticker...

    Thanks to both of you guys, I'll try with ticker wire and different number of turns. Just one more question, i feel a little bit confused.Main purpose of the coil, is it to reduce electric noise in...
  26. Replies
    57
    Views
    8,926

    Hi guys, I did make this dummy coil, just as an...

    Hi guys, I did make this dummy coil, just as an experiment, 6" diameter, 600 turns, 41AWG, 1.4 kOhm, I connected it to single coil pickup, straight to the amp.
    I expected at least a bit of regular...
  27. Replies
    21
    Views
    2,178

    Yes, especially with bias winding short to...

    Yes, especially with bias winding short to lamination (ground), he wouldn't be able to set bias current at all
  28. Replies
    21
    Views
    2,178

    Double post, sorry

    Double post, sorry
Results 1 to 28 of 36
Page 1 of 2 1 2