Search:

Type: Posts; User: copperheadroads; Keyword(s):

Page 1 of 18 1 2 3 4

Search: Search took 0.02 seconds; generated 58 minute(s) ago.

  1. These bobbins are heavily flawed...

    These bobbins are heavily flawed ...................
  2. Replies
    4
    Views
    206

    Don't scrap that pickup for the reason you didn't...

    Don't scrap that pickup for the reason you didn't sand the insulation off well enough . it my be a longshot but you can remove the finish from Plain enamel wire with the hot tip from the iron by...
  3. Good luck with that ,i have hundreds of covers...

    Good luck with that ,i have hundreds of covers here from china that don't fit American spec flatwork or just too cheap quality .just a little too tight to sit as it should causing the pickup to be...
  4. Replies
    10
    Views
    371

    I recently sourced a white ink stamp & tried...

    I recently sourced a white ink stamp & tried putting my logo on my flatwork before lacquer dipping & after it came out of the lacquer it was smeared too much to pick it out . i will try after...
  5. You can still see some of the dark goo on the...

    You can still see some of the dark goo on the grey fiber from the laser cutter ....I'd say FAKE .
  6. Replies
    9
    Views
    1,456

    I rewound the stock p-90 set that was in my 2011...

    I rewound the stock p-90 set that was in my 2011 les Paul . the bobbins were soft & not rigid as i thought & with no flare .
  7. Good source for 52mm humbucker bobbins

    I'm looking for a good source for 52mm humbucker bobbins with more of the PAF dimensions .most of the 52mm bobbins i've tried have small slug holes & they have cracked when i potted them . I have...
  8. Replies
    3
    Views
    359

    Are the bobbins textured ? & is there an another...

    Are the bobbins textured ? & is there an another unused lead wire hole in the bottom of the baseplate ? pics please !!!
  9. Replies
    29
    Views
    981

    I wax pot pickups all the time that is superglued...

    I wax pot pickups all the time that is superglued together with never any problem .
  10. Replies
    14
    Views
    1,203

    If your stretching the wire you will see higher...

    If your stretching the wire you will see higher dcr reading .
  11. You da man Pepe !!!!. :thumbsup:

    You da man Pepe !!!!. :thumbsup:
  12. Looking for a source to get some custom Keeper bars made ?

    Anyone got a source/machinist to get keeper bars made in bulk ? please PM me :)
  13. Replies
    14
    Views
    1,330

    lol .........As if I didn't wind a 1000 pickups...

    lol .........As if I didn't wind a 1000 pickups ............Just curious without doing a bunch of research ......First thing i thought would be to use bigger wire which i have ......
  14. Replies
    14
    Views
    1,330

    Dimarzio ,Humbucker from Hell ?

    Whats the deal with this pickup ? low output 5+k
  15. It's a great book & well worth the price . but if...

    It's a great book & well worth the price . but if your looking exact winding specs of a 59 strat or a PAF./ a shortcut in winding /rewinding . go buy it . you will learn something .
  16. Replies
    9
    Views
    2,712

    Maybe this is something i should be investigating...

    Maybe this is something i should be investigating .
  17. Replies
    9
    Views
    2,712

    So your saying even if the power rocker switch is...

    So your saying even if the power rocker switch is illuminated as well as the other channel indicators it could be the power switch ?
  18. Replies
    2
    Views
    755

    I'm just wondering if Gibson stays true to there...

    I'm just wondering if Gibson stays true to there wire colors if you look at the molex connector on Gibson pickups the wires are arranged different from bridge to neck
    the bridge is
    red
    black...
  19. Replies
    20
    Views
    1,757

    I would say he meant Leo Fender

    I would say he meant Leo Fender
  20. Replies
    20
    Views
    1,757

    To sum up Tele & strat pickups are not usually...

    To sum up Tele & strat pickups are not usually wound in the same direction or generally have the same Polarity (not including rwrp) & the average humbucker will not be in phase with either without...
  21. Replies
    20
    Views
    1,757

    This may be the confusing part , The direction...

    This may be the confusing part , The direction the bobbin is spinning is the opposite of direction the wire is wound on the bobbin .
  22. Replies
    2
    Views
    755

    Gibson Quick connect question

    Any one know wiring color /pin out of the Gibson 5 wire connector ? The problem I'm having is I do believe the Neck & bridge pickup have different pin-out or wire colors are in different order .
  23. Replies
    12
    Views
    1,328

    So was the guitar working before the problem ? &...

    So was the guitar working before the problem ? & nothing was changed /rewired ?
  24. Replies
    20
    Views
    1,757

    With the typical way most humbuckers are wound &...

    With the typical way most humbuckers are wound & wired & polarity (south to screw coil) . the tele north up & wound opposite it usually is .
  25. Replies
    11
    Views
    1,274

    I think a may wind a smaller coil with 44 gauge...

    I think a may wind a smaller coil with 44 gauge with close to the p-90 number of turns & compare it to the traditional p-90 bobbin I'm using as a dummy .
  26. Replies
    11
    Views
    1,274

    I don't really like the tone of rw/rp in P-90's &...

    I don't really like the tone of rw/rp in P-90's & don't usually make p-90's with rw/rp ..I guess now it's turning into more of Pickup discussion .. I'm wondering about using smaller wire to make the...
  27. Replies
    11
    Views
    1,274

    Les Paul P-90 dummy coil wiring

    I'm here playing around with adding a dummy coil in my les paul that has P-90's I'm really think it's worth doing as I've tested it with test clips but I cant figure how to use 1 dummy coil for both...
  28. Replies
    9
    Views
    2,712

    I've resoldered all the bad joints & made sure to...

    I've resoldered all the bad joints & made sure to reflow all the joints on the regulators (All 3 of them) & once in a while the problem still comes back .
Results 1 to 28 of 499
Page 1 of 18 1 2 3 4