Search:

Type: Posts; User: copperheadroads; Keyword(s):

Page 1 of 18 1 2 3 4

Search: Search took 0.04 seconds; generated 15 minute(s) ago.

  1. Any one Dissect the EVH Wolf gang pickups ?

    I got a set here in my personal Wolfgang that I don't really want to disassemble them ,they are quite clear sounding for such an hot pickup . PM me if you don't want to in public .
  2. Replies
    5
    Views
    341

    I haven't potted a cover in some time ,I use dab...

    I haven't potted a cover in some time ,I use dab of Dap Kwik Seal .
  3. Replies
    13
    Views
    1,350

    Beef up the Jazz pickups output by start winding...

    Beef up the Jazz pickups output by start winding with smaller wire or finishing with smaller wire like 43 gauge so you will have to change & join wires half way through the wind .
  4. The JM is a pretty tough pickup to do starting...

    The JM is a pretty tough pickup to do starting out.
  5. Some PAF's have rusty Keepers

    Some PAF's have rusty Keepers
  6. Replies
    25
    Views
    1,262

    I'm using water based finish to dip my bobbins in...

    I'm using water based finish to dip my bobbins in & the ink is not holding up as it gets cloudy . Have not used nitro in years for bobbins . i will have to try it after they are wound & see it it...
  7. Just so you know I've never ever seen a brand of...

    Just so you know I've never ever seen a brand of humbucker where the coils were not wound in the same direction & with either Finish ends connected together or the start ends.
  8. These bobbins are heavily flawed...

    These bobbins are heavily flawed ...................
  9. Replies
    7
    Views
    623

    Don't scrap that pickup for the reason you didn't...

    Don't scrap that pickup for the reason you didn't sand the insulation off well enough . it my be a longshot but you can remove the finish from Plain enamel wire with the hot tip from the iron by...
  10. Good luck with that ,i have hundreds of covers...

    Good luck with that ,i have hundreds of covers here from china that don't fit American spec flatwork or just too cheap quality .just a little too tight to sit as it should causing the pickup to be...
  11. Replies
    25
    Views
    1,262

    I recently sourced a white ink stamp & tried...

    I recently sourced a white ink stamp & tried putting my logo on my flatwork before lacquer dipping & after it came out of the lacquer it was smeared too much to pick it out . i will try after...
  12. You can still see some of the dark goo on the...

    You can still see some of the dark goo on the grey fiber from the laser cutter ....I'd say FAKE .
  13. Replies
    9
    Views
    1,725

    I rewound the stock p-90 set that was in my 2011...

    I rewound the stock p-90 set that was in my 2011 les Paul . the bobbins were soft & not rigid as i thought & with no flare .
  14. Good source for 52mm humbucker bobbins

    I'm looking for a good source for 52mm humbucker bobbins with more of the PAF dimensions .most of the 52mm bobbins i've tried have small slug holes & they have cracked when i potted them . I have...
  15. Replies
    3
    Views
    597

    Are the bobbins textured ? & is there an another...

    Are the bobbins textured ? & is there an another unused lead wire hole in the bottom of the baseplate ? pics please !!!
  16. Replies
    29
    Views
    1,419

    I wax pot pickups all the time that is superglued...

    I wax pot pickups all the time that is superglued together with never any problem .
  17. Replies
    14
    Views
    1,593

    If your stretching the wire you will see higher...

    If your stretching the wire you will see higher dcr reading .
  18. You da man Pepe !!!!. :thumbsup:

    You da man Pepe !!!!. :thumbsup:
  19. Looking for a source to get some custom Keeper bars made ?

    Anyone got a source/machinist to get keeper bars made in bulk ? please PM me :)
  20. Replies
    14
    Views
    1,590

    lol .........As if I didn't wind a 1000 pickups...

    lol .........As if I didn't wind a 1000 pickups ............Just curious without doing a bunch of research ......First thing i thought would be to use bigger wire which i have ......
  21. Replies
    14
    Views
    1,590

    Dimarzio ,Humbucker from Hell ?

    Whats the deal with this pickup ? low output 5+k
  22. It's a great book & well worth the price . but if...

    It's a great book & well worth the price . but if your looking exact winding specs of a 59 strat or a PAF./ a shortcut in winding /rewinding . go buy it . you will learn something .
  23. Replies
    9
    Views
    3,171

    Maybe this is something i should be investigating...

    Maybe this is something i should be investigating .
  24. Replies
    9
    Views
    3,171

    So your saying even if the power rocker switch is...

    So your saying even if the power rocker switch is illuminated as well as the other channel indicators it could be the power switch ?
  25. Replies
    2
    Views
    813

    I'm just wondering if Gibson stays true to there...

    I'm just wondering if Gibson stays true to there wire colors if you look at the molex connector on Gibson pickups the wires are arranged different from bridge to neck
    the bridge is
    red
    black...
  26. Replies
    20
    Views
    2,043

    I would say he meant Leo Fender

    I would say he meant Leo Fender
  27. Replies
    20
    Views
    2,043

    To sum up Tele & strat pickups are not usually...

    To sum up Tele & strat pickups are not usually wound in the same direction or generally have the same Polarity (not including rwrp) & the average humbucker will not be in phase with either without...
  28. Replies
    20
    Views
    2,043

    This may be the confusing part , The direction...

    This may be the confusing part , The direction the bobbin is spinning is the opposite of direction the wire is wound on the bobbin .
Results 1 to 28 of 499
Page 1 of 18 1 2 3 4