Search:

Type: Posts; User: copperheadroads; Keyword(s):

Page 1 of 18 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    2
    Views
    165

    If you Call & bug them you should get ok service...

    If you Call & bug them you should get ok service But don't rely on there online service & full email box .
  2. Replies
    6
    Views
    278

    Are you fimiliar with the coil estimator ?

    Are you fimiliar with the coil estimator ?
  3. Replies
    10
    Views
    270

    Your going to need 43 gauge or smaller if it's a...

    Your going to need 43 gauge or smaller if it's a tele neck pickup .
  4. Replies
    1
    Views
    147

    2.3k to 2.5k if you can get that much wire on...

    2.3k to 2.5k if you can get that much wire on those little bobbins .
  5. Replies
    5
    Views
    438

    The new EVH Frankenstrat pickup is around 14.4k &...

    The new EVH Frankenstrat pickup is around 14.4k & could be alnico 2 like the wolfgang pickups . so a Duncan custom custom or custom 5 would be close .
  6. What type of quick connect are you referring to ....

    What type of quick connect are you referring to . the Molex connectors like Gibson has used & still use on some models ?
  7. Replies
    51
    Views
    6,268

    Merry Christmas everyone :)

    Merry Christmas everyone :)
  8. Replies
    12
    Views
    1,864

    Merry Christmas .

    Merry Christmas .
  9. Replies
    4
    Views
    425

    Tie the wires together & resolder the...

    Tie the wires together & resolder the connection/knot & use fingernail polish or tape to insulate it & continue winding ...if it's Plain Enamel you may want to sand some of the insulation off...
  10. Replies
    3
    Views
    420

    https://wire-cable-tubing.wireandcable.com/item/ma...

    https://wire-cable-tubing.wireandcable.com/item/magnet-wire/single-formvar-round-magnet-wire/item-15312
  11. Replies
    7
    Views
    751

    Hey David i have a spool of wire that kind of dry...

    Hey David i have a spool of wire that kind of dry when i'm winding (It kind of squeaks as it goes through the felt tensioner) & the result is a tighter coil than i'd like. i was thinking about...
  12. Replies
    6
    Views
    527

    I've been also looking for a better source for...

    I've been also looking for a better source for springs , most you find are 1" like in the that link but finding them 1-5/8" /40mm is tough
  13. Replies
    4
    Views
    536

    I wonder how good of a job you can do with one of...

    I wonder how good of a job you can do with one of those cheap 3-D printers
  14. Replies
    7
    Views
    751

    The outer 43 gauge is shorted to the inner coil...

    The outer 43 gauge is shorted to the inner coil or just several shorts in the 43 gauge .I have had some very strange readings with 43 gauge wire . but it is usually cause I've stretched the wire &...
  15. I have a spool of Heavy build awg44 (Shehav) ....High output Humbucker or ..?

    .High output Humbucker or ...i wonder about goldfoil pickups


    44 gauge wire with double build wire which is same diameter as awg 43 . feel free to comment ..
  16. Any one Dissect the EVH Wolf gang pickups ?

    I got a set here in my personal Wolfgang that I don't really want to disassemble them ,they are quite clear sounding for such an hot pickup . PM me if you don't want to in public .
  17. Replies
    5
    Views
    969

    I haven't potted a cover in some time ,I use dab...

    I haven't potted a cover in some time ,I use dab of Dap Kwik Seal .
  18. Replies
    13
    Views
    1,761

    Beef up the Jazz pickups output by start winding...

    Beef up the Jazz pickups output by start winding with smaller wire or finishing with smaller wire like 43 gauge so you will have to change & join wires half way through the wind .
  19. The JM is a pretty tough pickup to do starting...

    The JM is a pretty tough pickup to do starting out.
  20. Some PAF's have rusty Keepers

    Some PAF's have rusty Keepers
  21. Replies
    25
    Views
    2,126

    I'm using water based finish to dip my bobbins in...

    I'm using water based finish to dip my bobbins in & the ink is not holding up as it gets cloudy . Have not used nitro in years for bobbins . i will have to try it after they are wound & see it it...
  22. Just so you know I've never ever seen a brand of...

    Just so you know I've never ever seen a brand of humbucker where the coils were not wound in the same direction & with either Finish ends connected together or the start ends.
  23. These bobbins are heavily flawed...

    These bobbins are heavily flawed ...................
  24. Replies
    7
    Views
    1,054

    Don't scrap that pickup for the reason you didn't...

    Don't scrap that pickup for the reason you didn't sand the insulation off well enough . it my be a longshot but you can remove the finish from Plain enamel wire with the hot tip from the iron by...
  25. Good luck with that ,i have hundreds of covers...

    Good luck with that ,i have hundreds of covers here from china that don't fit American spec flatwork or just too cheap quality .just a little too tight to sit as it should causing the pickup to be...
  26. Replies
    25
    Views
    2,126

    I recently sourced a white ink stamp & tried...

    I recently sourced a white ink stamp & tried putting my logo on my flatwork before lacquer dipping & after it came out of the lacquer it was smeared too much to pick it out . i will try after...
  27. You can still see some of the dark goo on the...

    You can still see some of the dark goo on the grey fiber from the laser cutter ....I'd say FAKE .
  28. Replies
    9
    Views
    1,987

    I rewound the stock p-90 set that was in my 2011...

    I rewound the stock p-90 set that was in my 2011 les Paul . the bobbins were soft & not rigid as i thought & with no flare .
Results 1 to 28 of 500
Page 1 of 18 1 2 3 4