Search:

Type: Posts; User: The Dude; Keyword(s):

Page 1 of 18 1 2 3 4

Search: Search took 0.05 seconds.

  1. Thread: Toaster oven

    by The Dude
    Replies
    14
    Views
    266

    I remember that, too. You had to walk 3 miles- up...

    I remember that, too. You had to walk 3 miles- up hill both ways- in a blizzard, and pull the boy scouts back to the fire location in a wagon with no wheels (because they hadn't yet invented the...
  2. Thread: Toaster oven

    by The Dude
    Replies
    14
    Views
    266

    Back in my day, they didn't even have fire yet.

    Back in my day, they didn't even have fire yet.
  3. Replies
    39
    Views
    547

    I've run into this before- even worse when...

    I've run into this before- even worse when someone has stripped the heads out leaving you nothing to grab onto. I'll take a dremel tool and grind a slot in the screw head(s) and use a straight slot...
  4. Replies
    25
    Views
    276

    Parts Express has a large selection of tweeters....

    Parts Express has a large selection of tweeters. I'd think you could find something similar. Also, lots of the old console stereos used similar style tweeters. If you know of any junked out laying...
  5. Replies
    17
    Views
    261

    Nice neat and tidy build and great pics!

    Nice neat and tidy build and great pics!
  6. Replies
    41
    Views
    8,680

    The resistor might be there to abate some...

    The resistor might be there to abate some switching noise. Just a guess without seeing where it is.
  7. Replies
    11
    Views
    288

    ...... and no wonder the tubes fried!

    ...... and no wonder the tubes fried!
  8. Replies
    6
    Views
    221

    If I'm not mistaken: To reset, hold down both...

    If I'm not mistaken: To reset, hold down both foot switches and power up.
  9. Ditto on the paper caps. Looks like a good refurb...

    Ditto on the paper caps. Looks like a good refurb project.
  10. Replies
    2
    Views
    165

    Is this the right one? 56594

    Is this the right one?

    56594
  11. Replies
    52
    Views
    800

    Yes, the speaker cone should move out if battery...

    Yes, the speaker cone should move out if battery + is to speaker + (generally). You may have a shifted speaker gap- magnet/pole piece problem. I'd try the amp with a known good speaker. If you push...
  12. I know you don't want to fix it, but posting the...

    I know you don't want to fix it, but posting the schematic if someone wants to have a look. According to Carvin, the AG200 and AG300 share a schematic. What's wrong with it?
    ...
  13. Replies
    52
    Views
    800

    Yes, jump fx send to return and plug the guitar...

    Yes, jump fx send to return and plug the guitar into the input jack as you normally would. This takes the switching jack out of the equation.

    If that doesn't work, I'd also check plate voltages...
  14. Replies
    13
    Views
    405

    I'll add another vote for the Pace. Once you have...

    I'll add another vote for the Pace. Once you have one, it's hard to imagine working without it. If you hunt around eBay, you can often find good used ones at decent prices.
  15. Replies
    6
    Views
    184

    Green/yellow is usually center tap for the 6.3V...

    Green/yellow is usually center tap for the 6.3V filament winding. You can check it with your meter to the outside windings for verification.

    Are you measuring across the 5V winding (wire to wire),...
  16. Replies
    51
    Views
    4,011

    I'm wondering if you have an oscillation problem....

    I'm wondering if you have an oscillation problem. Did you replace C46 or just remove it? Do you have a scope? If so, scope the output and see if you spot any oscillation.
  17. Replies
    8
    Views
    259

    Signal comes out of the volume board through C32,...

    Signal comes out of the volume board through C32, then through the FET Q10, then through C7 to the base of Q3. Do you have signal anywhere on that path? If so, where does it get lost?
  18. For the record, I was only kidding. :thumbsup:

    For the record, I was only kidding. :thumbsup:
  19. Replies
    63
    Views
    9,002

    Sticky: Looks like they might go after Trump properties,...

    Looks like they might go after Trump properties, first. (I'll bite my tongue now.)
    ...
  20. If Kanye had a genius moment, it was an accident....

    If Kanye had a genius moment, it was an accident.


    Edit:...... and Leo, I was hovering over the thumbs down button for a minute because you didn't recognize Neil. ;)
  21. Replies
    51
    Views
    4,011

    ^^^^ Yes, that for bias drift. The problem with...

    ^^^^ Yes, that for bias drift. The problem with C46 is that it's rated voltage is too low from the factory and often burns or shorts. I always replace it with a higher rated cap as a matter of...
  22. Replies
    51
    Views
    4,011

    FWIW: Both "the C46 problem" and the "bias drift...

    FWIW: Both "the C46 problem" and the "bias drift problem" are known issues for this amp and are separate issues.
  23. Replies
    3
    Views
    129

    Many of the Kustom schematics are by circuit...

    Many of the Kustom schematics are by circuit board instead of model number. Check your circuit board numbers against those on this page (link below). If that doesn't help, please list the numbers on...
  24. Replies
    79
    Views
    5,524

    Generally, if an amp won't bias, there's still a...

    Generally, if an amp won't bias, there's still a problem and you shouldn't continue to run it. It's time to shut down and continue hunting. Lack of bias is an indication of a problem. Check any...
  25. Replies
    9
    Views
    239

    Do you have a schematic so we can see what's...

    Do you have a schematic so we can see what's going on in the circuit?
  26. With no tubes but the rectifier in the amp, there...

    With no tubes but the rectifier in the amp, there is little or no conduction, so supply voltages will be high. Did you check the screen voltage on the output tube?
  27. 56534

    56534
  28. Gotcha. The can is three separate caps. The +...

    Gotcha. The can is three separate caps. The + terminals are designated with symbols on the side of the can, usually. They share a common ground, which is usually the can itself. I suspect a...
Results 1 to 28 of 500
Page 1 of 18 1 2 3 4