Search:

Type: Posts; User: nevetslab; Keyword(s):

Page 1 of 18 1 2 3 4

Search: Search took 0.02 seconds.

  1. I thought I had a full photo on this Deluxe...

    I thought I had a full photo on this Deluxe Reverb where I had tweaked the leads for V5 for minimum ticking. It's the stock Fender 'bug', and the copper leads are nearest the tube wires, putting the...
  2. Replies
    10
    Views
    152

    What DrGonz 78 said ^^^^^^, or perhaps a broken...

    What DrGonz 78 said ^^^^^^, or perhaps a broken trace, to restore the xstr's emitter to the circuit?

    As to WHY the pair on the one side failed........were these the non-Sanken Substitute parts? ...
  3. Replies
    12
    Views
    145

    A recent PCB trace burn repair done on an Aguilar...

    A recent PCB trace burn repair done on an Aguilar DB 751:

    54038 54039 54040

    After having scraped away all of the chared remains, which took going down a full level of the fiberglass layer, I...
  4. You could just leave the speaker connected on...

    You could just leave the speaker connected on this 'Reverb Tank EQ Amp, just to be safe. You're using this amp's Volume control (and Master, if it has one) to set the drive level to the Reverb tank...
  5. I like the thought of that!!

    I like the thought of that!!
  6. Replies
    12
    Views
    145

    Yes, there are two traces. I've shown them in...

    Yes, there are two traces. I've shown them in RED, adding them to your photo below:

    54037
  7. Replies
    10
    Views
    152

    SWR SM900 Evolution

    There have been 3 versions of the SM900, as far as I've seen in our rental inventory. From the front, they all pretty much look the same, but radically different inside. Some images of the amp...
  8. Replies
    16
    Views
    190

    I don't recall the 400Hz Standard Test Frequency...

    I don't recall the 400Hz Standard Test Frequency for defining nominal impedance. I think speaker mfgrs use the 0 phase frequency in the low midrange trough where impedance Q is broadest. Changes...
  9. While I've never tried this, taking the Reverb...

    While I've never tried this, taking the Reverb Output signal from it's 12AT7 circuit via the low impedance transformer, feeding a stand-alone equalizer, such as a 3 or 4-band parametric Equalizer,...
  10. Replies
    16
    Views
    190

    Very few of us have a multimeter that has VERY...

    Very few of us have a multimeter that has VERY FAST reading rates. Most economical Multimeters are 2-3 readings per second, to begin with. Using a Guitar as your signal source produces a complex...
  11. Replies
    37
    Views
    527

    While there are numerous amps that change power...

    While there are numerous amps that change power level by going from pentode to triode mode, or dropping the power supply potentials in half, those to me haven't changed the SPL level of the amp,...
  12. I went over to our other building down the street...

    I went over to our other building down the street & around the corner to give a look/listen to another of the Magnatone amps in our inventory. As I suspected, you don't need either the foot switch...
  13. Replies
    11
    Views
    272

    To show graphically what Helmholtz just stated,...

    To show graphically what Helmholtz just stated, where in normal use, the sounds from the organ will rarely dwell at the 'nominal' impedance value, and more like twice that value as a average would be...
  14. I've looked thru those on Google, as well as...

    I've looked thru those on Google, as well as MagnatoneAmps website. This is a current production model, so I'm sure it wouldn't be posted anywhere. I haven't yet gone to Magnatone on this. I was...
  15. Replies
    32
    Views
    858

    Hey..........that looks like a NICE tool! It...

    Hey..........that looks like a NICE tool! It reminds me a lot of the Leister Hot Air Gun, at 1/10 the price. I'm tempted to pick one of these up myself, along with that collection of nozzles.
  16. I believe it is MPS (Magnatone Panoramic Stereo)

    I believe it is MPS (Magnatone Panoramic Stereo)
  17. Replies
    11
    Views
    272

    I gather there is a Direct Out from the organ, so...

    I gather there is a Direct Out from the organ, so you're just looking to mute the speaker? Depending on where that direct out is from, using the dummy load will at least remove the sound from the...
  18. Magnatone Panormic Stereo Combo--Vibrato/Tremolo not working

    One of our Mangatone Panoramic Stereo Combo amps came over with no reverb, with a broken internal xfmr pin wire that I wasn't able to restore, so had to order another 4AB2C1B tank....put a 4AB3C1B...
  19. Replies
    16
    Views
    404

    Are you referring to the internal thermal fuse...

    Are you referring to the internal thermal fuse buried inside the windings? Class B insulation is 130 deg C, so you'd be safe using an OOR Thermal Fuse in the 115 deg C to 130 deg C, which would have...
  20. Replies
    14
    Views
    258

    This is what I love about this forum. There's...

    This is what I love about this forum. There's ALWAYS something new to discover in how stuff was built over the ages. Never until now have I seen a pair of dedicated speakers used for the Reverb,...
  21. Replies
    16
    Views
    404

    While always using industry standard AC Mains...

    While always using industry standard AC Mains fuses carrying 250VAC ratings from any of the normal sources (Bel, Bussman, Littelfuse, Schruter, etc), it still never fails to surprise me finding a...
  22. Replies
    16
    Views
    404

    Excellent document, now added to my database for...

    Excellent document, now added to my database for further study. Thanks for providing that!
  23. Replies
    16
    Views
    404

    If you have an AC Mains Power Analyzer, or an...

    If you have an AC Mains Power Analyzer, or an accurate AC RMS Ammeter, you'd start with probably a 3A S/B fuse installed. Run the amp up to full power at High Line (127VAC, assuming you have a...
  24. I put everything back together. Easy to loose...

    I put everything back together. Easy to loose track of which screw holes thru the two heat sinks go to the chassis standoffs, and which ones are for the two fans that only screw into the heat sinks,...
  25. OK, having connected my HP 6227B 0-25VDC/0-2A...

    OK, having connected my HP 6227B 0-25VDC/0-2A Dual Tracking supply to the Ground pin & +/- terminals of the LV bridge (passing current thru the two supply fuses F3 & F4, I ran the supplies up while...
  26. You're right. I've never given the absence of...

    You're right. I've never given the absence of reverb tank loading on the Driver Xfmr a second thought, when I have to pull the chassis from the cabinet, while the tank is well secured inside the...
  27. Back to the original problem with the amp, which...

    Back to the original problem with the amp, which turned out to be this shorted 37099 Driver Xfmr Primary.........I've never encountered one of these failing that way. For a very brief time when I...
  28. Arciing evidence found on the lower voltage middle pins/sockets of AC Secondary wiring

    OK, I think I've found the culprits. On the 7-pin PCB header, which receives the three power xfmr secondary coils, the middle LV winding having a Center Tap, those three middle terminals showed...
Results 1 to 28 of 500
Page 1 of 18 1 2 3 4