Search:

Type: Posts; User: g1; Keyword(s):

Page 1 of 18 1 2 3 4

Search: Search took 0.06 seconds; generated 1 minute(s) ago.

  1. Were these parts all there when it was running...

    Were these parts all there when it was running EL34's? If not, which did you change?
  2. Replies
    35
    Views
    653

    You don't have a spare LCD for that baby do you? ...

    You don't have a spare LCD for that baby do you? I have a 310 (same as HD series) but the display got broken. Great meter. I have a spare multi-processor and the service manual if you need...
  3. Replies
    17
    Views
    333

    But on top he's got a guitar he painted to match,...

    But on top he's got a guitar he painted to match, and now he's just going to let the amp go!
  4. Replies
    24
    Views
    6,464

    Well, I couldn't think of a more deserving guy to...

    Well, I couldn't think of a more deserving guy to have a part named after him. ;)
  5. Replies
    33
    Views
    474

    How hot is the idle current? Measure the DC...

    How hot is the idle current? Measure the DC across the 6.8 ohm resistors. Typically these MM amps are biased very cold, around 6mA, so you should set for about 40mV across each of those 6.8 ohms....
  6. This gets a little interesting as to whether we...

    This gets a little interesting as to whether we are talking ground, chassis, or common. As far as I know for this model, the speaker jack is not insulated from chassis. So Helmholtz method is...
  7. Good job, but a tip for future reference: since...

    Good job, but a tip for future reference:
    since you are only concerned with removing the short from the supply rails, you only need to desolder the power pins on those IC's, so 8 connections in...
  8. Replies
    24
    Views
    6,464

    Curious as to whether this was a NOS part, or one...

    Curious as to whether this was a NOS part, or one of the modern repro's like xvive?
  9. Replies
    7
    Views
    160

    Faulty filter caps where you have high AC ripple...

    Faulty filter caps where you have high AC ripple can give odd readings depending on the meter. As you have reported low DC on the filter caps, it could be that there is high AC ripple. In that case...
  10. Replies
    51
    Views
    1,105

    Sorry to jump in the middle here about tubes you...

    Sorry to jump in the middle here about tubes you don't want to talk about ( ;) ), but since the issue was brought up...
    Did this circuit work correctly for you (or others) with the 6C10 instead of...
  11. Replies
    116
    Views
    1,495

    Agree but the problem is going the other way, as...

    Agree but the problem is going the other way, as Justin outlined above. For example the era when Marshall dropped EL34's due to reliability issues and had stickers on their amps that said 'equipped...
  12. Replies
    116
    Views
    1,495

    The JJ and re-issue 'tung-sol' 5881's are 23W...

    The JJ and re-issue 'tung-sol' 5881's are 23W tubes and should be biased accordingly. (26W rating is for triode configuration as per JJ datasheet)
    It's unfortunate that when the 5881 moniker was...
  13. No elastomers or 'zebra strips' between the...

    No elastomers or 'zebra strips' between the display and board, like is often used for DMM displays?
  14. Replies
    13
    Views
    342

    What is the AC voltage at the actual primary...

    What is the AC voltage at the actual primary leads of the power transformer?
    What is the heater voltage?
  15. Replies
    13
    Views
    342

    Is heater voltage also low?

    Is heater voltage also low?
  16. What does your meter say on diode check across...

    What does your meter say on diode check across those zeners?
    There's not a lot running off those low voltage rails. 3 IC's and a couple other items. Easy enough to de-solder the IC supply pins (4...
  17. Did you check if it is working? Just wondering...

    Did you check if it is working? Just wondering if there could have been a mix-up and you got shipped something that was actually a defective return or something like that? (although I'd be surprised...
  18. Replies
    13
    Views
    342

    You set bias for total current through standby...

    You set bias for total current through standby switch?
    That is what they specify.
    If you set for 75mA idle current at power tube, it would certainly pull down all the voltages.
  19. Sounds like this unit matches the Hot Rod, not...

    Sounds like this unit matches the Hot Rod, not the Blues.
    Here is Rev.B which shows the items you mentioned:
  20. Don't rewire it to match a different schematic....

    Don't rewire it to match a different schematic.
    Can you post some pictures of the board, including the bias circuit area and any board number markings?
  21. Replies
    77
    Views
    2,155

    If yours has a coupling cap into the tank, like...

    If yours has a coupling cap into the tank, like C43, check that signal is getting through it.
  22. Replies
    77
    Views
    2,155

    Do either of these schematics match up? 55253

    Do either of these schematics match up?

    55253
  23. Replies
    12
    Views
    339

    :thumbsup: on the melted in staples. Great way...

    :thumbsup: on the melted in staples. Great way to add strength when bonding plastic.
  24. Replies
    77
    Views
    2,155

    All I can say without a schematic is that if you...

    All I can say without a schematic is that if you can't get a real loud response from the springs with the reverb and volume turned up, then I think the problem is on the recovery side of the reverb...
  25. Replies
    7
    Views
    203

    I've had problems with the shield wire in the...

    I've had problems with the shield wire in the wiring harness to the preamp with these, or the connectors.
  26. Every time you have described the sound it sounds...

    Every time you have described the sound it sounds like the amp is picking up some kind of external interference.
    Have you tried it at other locations? How have you determined the noise is not being...
  27. Thread: Ampeg J12-T

    by g1
    Replies
    6
    Views
    196

    Have you verified with your meter that 0 on the...

    Have you verified with your meter that 0 on the pot is 0 ohms?
    Aside from that, the pulsing could be coupled through the power supply, C22 would be a suspect.
  28. Replies
    13
    Views
    299

    So if it measures the same as other diodes, and a...

    So if it measures the same as other diodes, and a new one also measures same, it should be ok.
    Meantime, what is the unit you are trying to fix and what is the fault? :)
Results 1 to 28 of 488
Page 1 of 18 1 2 3 4