Search:

Type: Posts; User: glebert; Keyword(s):

Page 1 of 18 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    38
    Views
    578

    When you do this do you also need to account for...

    When you do this do you also need to account for the higher impedance of the 6V6s, so it becomes very similar to pulling two tubes (?). If you go down to two 6V6s would you get two doublings of...
  2. Replies
    38
    Views
    578

    Fire your customer

    Fire your customer
  3. Replies
    2
    Views
    115

    Dumb question on power supply

    Can I use a general purpose 19ish VDC laptop AC/DC brick as a negative power supply? More importantly, can I use two bricks to get +/- 19V rails? I have a Marshall Lead 12 with a bad transfomer and...
  4. Oddly enough, right now my HRDlx is mostly being...

    Oddly enough, right now my HRDlx is mostly being used as a thing to tilt my Bassbreaker 007 combo against. Just got the 007 in a trade and am enjoying it quite a bit. Need to try it with an external...
  5. Thread: RELISH guitar

    by glebert
    Replies
    18
    Views
    319

    I think this is regarding the "unbreakable...

    I think this is regarding the "unbreakable headstock" claim.
  6. Thread: RELISH guitar

    by glebert
    Replies
    18
    Views
    319

    My local music store had some on display for a...

    My local music store had some on display for a while so I played one a little, not plugged in. Didn't like it at all.
  7. Replies
    44
    Views
    919

    I think you should go buy the cheapest amp that...

    I think you should go buy the cheapest amp that says it can do 2 ohms at just barely the total power you want to run the subs,that way you won't be paying for any extra watts. Then when it fails you...
  8. Replies
    44
    Views
    919

    Watts are cheap these days, I would just get an...

    Watts are cheap these days, I would just get an amp that has the power rating you want at 8 ohm. Ignore the 4 ohm rating, this won't apply to you, and you will be running the amp at far less than its...
  9. Sticky: The fact that it does it only at the extreme...

    The fact that it does it only at the extreme positions of the volume pot make me wonder if someone could be wrong with that part.
  10. Nice job! Glad you got what you wanted.

    Nice job! Glad you got what you wanted.
  11. Replies
    1
    Views
    97

    Coin base power tube retention

    I've got a Peavey Classic 60/60 tube power amp that someone retubed with 5881 WXT (I think) "coin base" tubes. They work and sound fine, but I worry about tube retention. The amp has beartrap style...
  12. And it looks like big guitar picks!

    And it looks like big guitar picks!
  13. Replies
    16
    Views
    393

    Have you tried a different speaker? Just trying...

    Have you tried a different speaker? Just trying to rule out any external thing.
  14. I didn't peel back the tolex, just cut right...

    I didn't peel back the tolex, just cut right through it with my circular saw. It didn't pull away from the wood at all. If it did it can be glued back down. If there is any exposed wood or gaps I...
  15. Was just reading a story about Marty Stuart...

    Was just reading a story about Marty Stuart finding a tab of acid inside the cavity of Clarence White's Telecaster.
  16. Looks good. I have had pretty good luck just...

    Looks good.

    I have had pretty good luck just cutting the combo cabinet down into a head. I used a circular saw and cut sections out of the sides to move the bottom up and removing the speaker...
  17. Replies
    12
    Views
    337

    This works well for me for odors:...

    This works well for me for odors: https://music-electronics-forum.com/showthread.php?t=45883
  18. Nice write up. I will probably use this when I go...

    Nice write up. I will probably use this when I go to fix the one that has been sitting in my closet untouched for the past year or so.
  19. Replies
    12
    Views
    337

    Maybe Moldex or Wet and Forget Mold Remover? When...

    Maybe Moldex or Wet and Forget Mold Remover? When I had a water leak that gotten into (but not ruined) drywall my contractor/neighbor had me spray the area that had gotten wet with that to prevent...
  20. My favorite jazz tone with a Bandit (and the...

    My favorite jazz tone with a Bandit (and the Specials I have had were basically Bandits with 2x power) was putting in a 12" bass speaker and closing up the back of the cabinet. Made it a lot thicker...
  21. Those amps are stupid loud.

    Those amps are stupid loud.
  22. Replies
    7
    Views
    279

    I would try to narrow it down to preamp or...

    I would try to narrow it down to preamp or poweramp. Since you have a master volume if you turn that down does the noise go away? If so it is in the preamp, and you can see if any of channel controls...
  23. Replies
    0
    Views
    83

    Peavey Classic 50 effects loop hum

    Just got this amp working again and prepping it for sale. One issue is that there is a bit of a hum, present on both channels, only control that changes it is MV. Hum gets noticeable when MV gets to...
  24. I'm not saying you shouldn't build a kit or from...

    I'm not saying you shouldn't build a kit or from scratch. There is another option that I have been looking at, just to get a bit more immediate gratification. There is a company called KLD that sells...
  25. Replies
    6
    Views
    185

    Found this thread that indicates sometimes the...

    Found this thread that indicates sometimes the digital chips need to be reseated. https://forums.fender.com/viewtopic.php?f=13&t=106491
  26. Replies
    9
    Views
    258

    I use an old Telequipment single trace tube scope...

    I use an old Telequipment single trace tube scope for my 98%, works fine for signal tracing and what not. I have a Tek TDS 420a four channel digital scope that I got for $14 from a thrift shop. I...
  27. Solder joints on tube sockets?

    Solder joints on tube sockets?
  28. Glad to hear that works, almost anything would be...

    Glad to hear that works, almost anything would be better than going through Egnater to get a replacement. I looked around for aftermarket when I did a Egnater Rebel but could only find Mercury as a...
Results 1 to 28 of 500
Page 1 of 18 1 2 3 4