Search:

Type: Posts; User: SoulFetish; Keyword(s):

Page 1 of 18 1 2 3 4

Search: Search took 0.02 seconds.

  1. also, you can try boltdepot.com...

    also, you can try boltdepot.com
  2. are you sure they aren't standard M3 x 1?

    are you sure they aren't standard M3 x 1?
  3. The contact area in the middle terminal (8Ω...

    The contact area in the middle terminal (8Ω selection) is the switch position that was and is normally in. It was not cleaned by the switching action, nor did deoxit remove the discoloration. I don't...
  4. Anyone want a Kustom KB200 Toroid transformer pull?

    Just pay the cost of packing/shipping.
    I donít feel like sitting on this one and waiting for the right buyer to come along
  5. Replies
    10
    Views
    215

    I've seen examples of what both you and the Dude...

    I've seen examples of what both you and the Dude are describing. To your point, Enzo, failure of the solder joints have been the most common failure I've come across. But I still think the Dude's...
  6. I just checked the datasheet for the HS series...

    I just checked the datasheet for the HS series switches and they do have some models with silver plating.
    I've just been reading up on silver sulphide, silver plated contacts, and problems leading...
  7. Take a look at this Impedance selector switch. Not sure what to make of these terminals?

    Not sure if I've ever seen one in this condition?? This is labeled as NKK, which makes high quality switches, but I've never seen any of their switch terminals suffer this kind of blueing before....
  8. downside is, now "they" know where you live

    downside is, now "they" know where you live
  9. Looking to get some recommendations for inductance meters.

    I have almost no experience with any model, so I don't want to put any limitations on the price range. If you have any favorite cheap ones, let's start there. That way I can start to get a sense of...
  10. Yeah, I thought about maybe using batteries to...

    Yeah, I thought about maybe using batteries to power it up. Its is convenient not having to worry about turning it on and off, or batteries though.
    One thing that concerns me about powering it from...
  11. I also realized that I don't need to replace the...

    I also realized that I don't need to replace the existing cables either. If you look at the orange and yellow wires which supply the 6.3VAC power for the supply, they only use one of the tubes for...
  12. Right, there were a couple of things I was...

    Right, there were a couple of things I was thinking about to minimize this. First, I was thinking about installing a MOV across the plate to cathode pins to protect against overvoltage (figure...
  13. The Bias King Pro modification that it desperately needs

    I got this as surplus from a store I used to work at for a fraction of it's retail price - (but still not cheap, by any means). I bought it with the hopes that it would make the bias procedure much...
  14. Nicely done!

    Nicely done!
  15. So, lifting the 100k resistor eliminates the...

    So, lifting the 100k resistor eliminates the negative feedback. But it doesn't necessarily solve a problem cause by a ground loop. In order to start troubleshooting that you have to start to trace...
  16. I just had an 800 in the shop for an unrelated...

    I just had an 800 in the shop for an unrelated rush repair job. After fixing the amp's issue it came in for and installing 4 new EL34s, I noticed a moderately bothersome hum just like the one you...
  17. If you're pretty sure you've identified the...

    If you're pretty sure you've identified the primary leads, there are a couple of techniques to determine what the output lead orientation is. Assuming you know that you have taps for 4,8, and 16Ω,...
  18. Replies
    9
    Views
    320

    In this case, its not the PT rattling. In these...

    In this case, its not the PT rattling.
    In these series of amps, the ceramic snubber caps cause mechanical/acoustic buzzing which is audible. It's nothing to worry about, but it is annoying.
    One...
  19. I found it! (the air coil shielding solution)...

    I found it! (the air coil shielding solution)
    Fits all the criteria.
    - should house both inductors, making efficient use of space.
    - easily mounted
    - ported to run wires in and out of the...
  20. . So, it's not pliers or cutters, but I wanted...

    .
    So, it's not pliers or cutters, but I wanted to share the latest addition to the shop which just arrived.

    ...
  21. I was wondering about that early

    I was wondering about that early
  22. I would personally stay with 6L6s, and upgrade...

    I would personally stay with 6L6s, and upgrade the replacement OT if needed.
    But, if you did switch to 6V6s, you're going to want to consider a couple of things - assuming you're going to keep the...
  23. Replies
    2
    Views
    173

    Tedmich. dude, I've been looking for enclosures...

    Tedmich. dude, I've been looking for enclosures like this (or at least in this size)! This is a good tip. :thumbsup:
  24. Replies
    45
    Views
    5,072

    If you'll forgive me going off topic for a sec,...

    If you'll forgive me going off topic for a sec, have there been any bob p sightings around the intertoobs at all?
    It's been a while, and I was wondering if there was any way of reaching out to him...
  25. Replies
    7
    Views
    265

    You can’t keep that carbon on the board, it is...

    You can’t keep that carbon on the board, it is conductive. There are high voltage traces running through the affected area which is now contaminated.
  26. Is it the handles that smell like that? All I...

    Is it the handles that smell like that? All I know is something happens as they sit in a tool box over the years that makes the whole thing smell like complete puke.
  27. My Dad has had a set of these in his toolbox for...

    My Dad has had a set of these in his toolbox for as long as I can remember.



    HA! We do the same thing.
    They would almost fit a normal cordless drill chuck fine, but those "wings" at the base...
  28. nice woodwork! Mahogany?

    nice woodwork! Mahogany?
Results 1 to 28 of 500
Page 1 of 18 1 2 3 4