Search:

Type: Posts; User: mozz; Keyword(s):

Page 1 of 18 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    7
    Views
    215

    Well i kind of meant the note is ringing out, and...

    Well i kind of meant the note is ringing out, and when you do a fingering change it was accentuating any small mistakes i made. Where as the note decays and you switch to the next chord, kind of...
  2. Replies
    7
    Views
    215

    The brass inserts I used went into maple necks. 2...

    The brass inserts I used went into maple necks. 2 were teles and 2 strats. You need to drill the correct size holes with a stop and then thread them in with a big ass slotted screwdriver. Slightly...
  3. Replies
    7
    Views
    215

    I use these on a few builds. 79c each...

    I use these on a few builds. 79c each
    https://www.albanycountyfasteners.com/10-32-brass-threaded-inserts-wood-400-332-p/117010.htm
    And this screw. @1 3/4"...
  4. Replies
    4
    Views
    136

    Here are 3 pictures of my Gretsch, 61?? not a...

    Here are 3 pictures of my Gretsch, 61?? not a chet model. Second has flash and third has no flash. If you want higher resolution or taken outside in the sun, email me direct at n3uvt at ptd dot net....
  5. Replies
    8
    Views
    240

    Your counter could also be off, contacts could be...

    Your counter could also be off, contacts could be bouncing. Post a picture of how full the bobbin is, someone here could tell you how many turns fit.
  6. Replies
    8
    Views
    189

    22 awg =3 amps Those other charts are for some...

    22 awg =3 amps

    Those other charts are for some special purpose, i would never run 32 amps through 14 awg yet is says 5.9 amps for power transmission?
  7. Replies
    10
    Views
    204

    Common problem with the silverface amps. I would...

    Common problem with the silverface amps. I would just clear over it to stop it from getting worse.
  8. Don't these actives use a 25k or 50k pot?

    Don't these actives use a 25k or 50k pot?
  9. Replies
    20
    Views
    452

    5 various spools of Litz wire for experiments,...

    5 various spools of Litz wire for experiments, which i will get to in about 8 years from now. I know 1 has 7 conductor, another has 20.
    584935849458495
  10. Replies
    9
    Views
    292

    A lot of LCR meters won't give you a good...

    A lot of LCR meters won't give you a good capacitance reading on a basic inductor, i usually calculate it out.
  11. Replies
    18
    Views
    377

    I'd lift one end, if it measures 300-360uf, leave...

    I'd lift one end, if it measures 300-360uf, leave it be.
  12. Replies
    12
    Views
    280

    Is that the model with all the problems of...

    Is that the model with all the problems of overheating?
  13. Replies
    57
    Views
    1,144

    If you dont have a scope, you can measure the DC...

    If you dont have a scope, you can measure the DC voltage on the filter caps, then measure the AC voltage at the same points. Post here and they will tell you what's acceptable AC ripple. (I myself...
  14. I think Mouser only charges the original...

    I think Mouser only charges the original shipping? Not sure. Have you tried Tayda for pedal parts?
  15. Replies
    14
    Views
    387

    Although using a analog meter will show polarity,...

    Although using a analog meter will show polarity, i use my digital Fluke when phasing a pair of pickups, works fine. Touch the tip of a small screwdriver to a screw pole piece, pull screwdriver away...
  16. Replies
    19
    Views
    732

    With no tone control, if anything you will have...

    With no tone control, if anything you will have more treble, slightly. A treble bleed only helps with the volume turned down, does nothing when on 10. I would wire it up with 1 vol, if needed you can...
  17. Replies
    8
    Views
    266

    I bought a thomas chassis for parts once, i think...

    I bought a thomas chassis for parts once, i think there was a 12v winding and i used it for the output tubes in series. The was also a small Leslie that went with it too.
  18. Replies
    38
    Views
    1,064

    2 battery packs, charge both. Have a switch to...

    2 battery packs, charge both. Have a switch to choose. Alternate between packs when needed, charge again when needed.
  19. Replies
    9
    Views
    648

    Some of those ceramic disk capacitors from back...

    Some of those ceramic disk capacitors from back then were about the cheapest cap you could buy. But many of them are still working good. I think they distort the sound or cause phase shifts or...
  20. Replies
    11
    Views
    366

    I've got a bunch of 2.7meg, i think these are...

    I've got a bunch of 2.7meg, i think these are Erie, if UK made i don't know how they got over here. They all measure exactly 3.4meg which seems odd but they were all stored in the same container...
  21. Some of those have odd sized dia shafts, so if...

    Some of those have odd sized dia shafts, so if you hard wire a new pot, the old knob will not fit. EDIT: looked at a Crate parts unit here and has different pots, 80's era.
  22. Replies
    11
    Views
    366

    Friend has a old fuzzface, original I think, that...

    Friend has a old fuzzface, original I think, that had those resistors. He wanted me to find some but if they are known to be bad could be a moot point. Maybe he's just trying to get it back to stock...
  23. Replies
    11
    Views
    366

    Who made those white resistors with the orange...

    Who made those white resistors with the orange ends?
  24. 2 different part numbers on the back, one is...

    2 different part numbers on the back, one is audio taper other is linear taper?
  25. Replies
    10
    Views
    297

    I think i would use RTV in this case, not glue or...

    I think i would use RTV in this case, not glue or epoxy. I can feel that speaker just from the picture. I have one in a 1x12 cabinet, it probably ripped the baffle screws out just from sitting there...
  26. Replies
    49
    Views
    991

    Capacitor across R4

    Capacitor across R4
  27. Replies
    5
    Views
    247

    Not familiar with those pots but would blast...

    Not familiar with those pots but would blast right here.
    57491
  28. Met Steve over the weekend and picked up the...

    Met Steve over the weekend and picked up the items. Very nice person and i thank him very much. Now to decide which project to do first. I think the Marshall cabinet with either a jtm45 or 18 watt.
Results 1 to 28 of 500
Page 1 of 18 1 2 3 4