In using my cheap laptop to run guitar amp sim software out to a sml.guitar amp.
1/4 guitar patch cord is reduced to the required 1/8" input of...
Announcement
Collapse
No announcement yet.
Search Result
Collapse
77 results in 0.0077 seconds.
Keywords
Members
Tags
-
Older Dell laptop mic in jack goes dead after 10 min
-
According to this article excerpt there is a risk of increased crossover dist. when lowering the screen grid voltage.
the screen voltage can...
-
Jeez...I should start a blog!
but while I'm here...
Someone in this forum mentioned that an EL84 when run in a low watt mode...
Leave a comment:
-
I like the looks of my 6au6s (actually they are 3au6) mostly because they are small I have two on hand LOL!
Good to know they have potential....
Leave a comment:
-
Getting back to my earlier post... Even though cathode biased, how can an el84 run with 12v B+ get cooking like with 300v plate voltage normally encountered?...Last edited by allsavy; 03-05-2010, 10:11 AM.
Leave a comment:
-
Ya know... those 6k6s kinda remind me of el84s with the front of the amp driven.
and that is different than a 6v6. A bit grainy but I wont...
Leave a comment:
-
Thanks for the tip re: 6K6
have only one to play with.
sounds like Like a 6v6 but with earlier breakup right?
...
Leave a comment:
-
yeah 1/4 watt in PP pentode mode!
I hope to use push pull pentodes in a low power scheme as a switchable alternative to my 2x 6L6 PP fender...
Leave a comment:
-
Leave a comment:
-
low B+ EL84
I saw a schematic online somewhere for a headphone amp that uses an EL84 SE output rated in mili-watts!
B+ around 12 v.
Is this even...
-
Yes using a self split PP will eliminate the need for a PI although a SE OT would be needed.
Perhaps this would be the way to go because my trying...Last edited by allsavy; 03-03-2010, 11:13 AM.
Leave a comment:
-
wont need a PI...Yeah you are right. Although I consider my existing LTP (also a 12au7) to be key to the sound I'm used to hearing from this amp (the fender)...
Leave a comment:
-
Thanks, I saw the firefly but can the grounded grid PP arraingement as such be used with a LTP PI?
wouldn't appear so. ????
Leave a comment:
-
I found this power tube switching method but can't make out the type of switch.
http://www.schematicheaven.com/boogi...ogie_blueangel...
Leave a comment:
-
Would I have to scale down the output voltages of my pi to in order to use a 12au7 in place of the 6L6s ?
Leave a comment:
-
-
Cool....thanks. Just what I wanted to hear!
perhaps I'll use this output scheme:
lunchbox amp.
Adam's...
Leave a comment:
-
self split 12au7 output
I'm in search of a low watt (>2 watt) output alternative to my favorite main guitar amp (fender pro style w/2-6L6 Push Pull pwr section driven by a long...
-
ThermionicScott, with the 6au6 what kind of pentode sound- like a 6v6 (round/muddy) or like a el84 (more articulate) ?
Leave a comment:
-
simply put a 5751 in v1 and try a 12au7 in the phase inverter. I did this to my amp although it has a long tail pair PI I replaced the tail resistor with...
Leave a comment:
-
I could not find any good reference for appropiate values to use a 12au7 as a phase inverter but since mt LTP had been changed from the typical fender 82k/100k...
Leave a comment:
Leave a comment: