Announcement
Collapse
No announcement yet.
Search Result
Collapse
38 results in 0.0068 seconds.
Keywords
Members
Tags
-
I have it going through a 4x12 Marshall at the moment and it is not the sound of a speaker rattling or buzzing. I was thinking it was the preamp overdriving...
-
"Farting" out problem lwer strings
OK, there are a few mods to the standard M1 schematic. I added a hi and low input with...Last edited by Rockn; 10-14-2010, 03:05 AM.
Leave a comment:
-
Almost done
This thing is finally almost done. Just waiting on some new pots and looking for a decent 8" speaker. It sounds pretty good...
Leave a comment:
-
Leave a comment:
-
It is a one off add-on for a Hammond amp. I cannot find any info on it or what it was used for and am assuming that it is a reverb amp with the R designation...
Leave a comment:
-
Most of the sub-mini amps I have seen have used Fender Reverb transformers. I would look up the datasheets because they are around and it is better to use...
Leave a comment:
-
Gotcha! I have been doing some modeling with PSUD and it is all starting to make sense now. Aside from all of the different tube manufacturers laying out...
Leave a comment:
-
Thanks for the info. I understand the majority of it as this applies for specing out a PT as well as an OT for an amp. The part about dropping the voltages...
Leave a comment:
-
I have tried using PSUD and have not fared very well. I understand how to add RC/LC filters and the different loads, but it still comes out wrong. Unless...
Leave a comment:
-
Power Supply Design
Is there any definitive simple tounderstand guide to building/designing the power section of a tube amp? I have found bits and pieces here and there and I...
-
I did look at TheHoj work on here and have gotten some ideas out of that. I would like to keep the 6EU7 section just to see how it works out instead of rewiring...Last edited by Rockn; 07-10-2010, 07:44 PM.
Leave a comment:
-
Getting the most out of a Bogen CHB-35A conversion
I recently acquired this Bogen amp and have done sme mods to it and it actually sounds pretty good if you want a really clean sounding amp with lots of chime....
-
It would directly replace the pickup that is in there. Unless the humbucker is coil tapped it should be a straight wire for wire replacement. Gibson's web...
Leave a comment:
-
amp build
There is quite a bit of room in this chassis to isolate stuff so getting the preamp away from the PT is not a problem. I think this...
Leave a comment:
-
Unknown amp conversion
I would like to convert an amp that I just purchased and wanted to get some input and advice. The amp in it's present state has a tube compliment of a 5Y3GT...
-
What ohm speaker are you using and is the NFB resistor of the correct size for the speaker you are using? The stage after the reverb section should be your...
Leave a comment:
-
Windings
Yes, I get the same voltages across both pairs. I suppose I would take the one with the highest current and use it for the two tubes...
Leave a comment:
-
This amp had a complement of 2 - 6AU6, 1 - 6X4, 1 - 6BQ5 and a 6AR5. One would assume that the hookup would be similar with the yellow supplying the 6X4 and...
Leave a comment:
-
Windings
Mine has a red pair, blue pair and a yellow pair. I was assuming the blue was a 6.3V pair since they were connected to the heaters...
Leave a comment:
-
Kalamazoo
Yea, the Kalamazoo was the closest configuration I could find to the original tube compliment. I will be using the 6X4 rectifier...Last edited by Rockn; 08-18-2009, 01:02 PM.
Leave a comment:
-
Standby switches
I have seen different applications for the standby switch as far as it's placement, and the majority of them have been right...
Leave a comment:
Leave a comment: