Announcement
Collapse
No announcement yet.
Search Result
Collapse
64 results in 0.0084 seconds.
Keywords
Members
Tags
-
Mmmmm............. I will have a dig through my archive and see if i can find and upload them
-
Yes this is an early D12 possible an very early one which also came under the Echolett brand.
I put this repair guide together for GDIY a few years...
- Likes 3
Leave a comment:
-
You also belive in faries I suspect....... think about it ? and I shall explain.
The update 1.11 is a firmware bin factory file for the basic DDX, ...Last edited by S2udio; 05-08-2019, 07:50 PM.
Leave a comment:
-
Hi just to make things clear, There is no such thing as a magic 1.11 DDX update file, you need to burn a new or reflash the existing one
There is no...
Leave a comment:
-
Start with recapping the PSU, its a simple must do for these mixers before going any further, sounds like a +/- 17v rail low opr missing.
Check out...
Leave a comment:
-
Check the fader board for dry joints/ bad ribbon cable.....there is an eprom up there as well that can go corrupt ,a while now since I had any trouble with...
Leave a comment:
-
As many have asked me, and i forgot the password on the original file here is the eeprom bin files with no password...
Leave a comment:
-
Mick as you are in the UK, Stewart at Xaudia is a helpful guy to contact about ribbons.
Xaudia Elektrik - Extinct Audio Equipment, Microphones &...
Leave a comment:
-
Leave a comment:
-
Changed the 32Mhz xtal ?
If that has no effect looks like the OS rom IC19 is possibly corrupt or worst case CPU death.
Try reflowing the CPU chip,...
Leave a comment:
-
No need to change those, they will probably outlive you !
About a volt offset ....is this measured disconected from the fader board,...Last edited by S2udio; 01-09-2016, 10:41 PM.
Leave a comment:
-
-
This is absolute +1, never get drawn into a pointless "IT sounds Like" debarcles.
Being involved in tech repair and a...
Leave a comment:
-
You also have to bear in mind,power monitor electronics take a hell of a vibration test .
Esspecially when given a hard time with the boom boom boys...
Leave a comment:
-
Chinese lead free solder,gets all of us sometime or another.
Just fixed a computer PSU for a mate.
Intermittently dead when turning on from...
Leave a comment:
-
These are not rocket science.....pardon the pun !
Sounds like someones just got no experience troubleshooting.
Go to the data sheet and digest.....the...
Leave a comment:
-
As i have said before .....you are wasting your time ,and mine ,most politely
The ddx file exchange will "Not work" unless you have a fully...Last edited by S2udio; 05-05-2015, 04:21 PM.
Leave a comment:
-
just to verify , That means you have ver 1.12 installed, Yes ?, I would Flash it anyway. could be a corrupt bit/flag
As stated in my previous...Last edited by S2udio; 05-04-2015, 10:52 AM.
Leave a comment:
-
My Quote....
I hope you saved the original config before writing over the data, just for good practice !
You need to also...Last edited by S2udio; 05-04-2015, 09:30 AM.
Leave a comment:
-
Yup will see if i can upload them....Watch this space
Attached
PM me for the password
Taken from a working DDX ,OS...Last edited by S2udio; 04-09-2015, 05:14 PM.
Leave a comment:
-
Thats fine if the CPU is is working and ready to recieve data.....obviously on a working mixer ?
Leave a comment:
Leave a comment: