Announcement
Collapse
No announcement yet.
Search Result
Collapse
48 results in 0.0054 seconds.
Keywords
Members
Tags
-
Haven't had time yet, probably won't be able to get to it for a while, I keep forgetting to order new fuses since I may need more than one got sidetracked...
- Likes 1
-
Q9 and Q10?
I'll have time tomorrow to check, but I don't have a fuse at the moment.
Leave a comment:
-
Stock fuse, was playing through it with no pedals and it was fine for maybe 10 minutes, plugged in the VFE pedal and tried it for a couple minutes and then...Last edited by redkurn; 04-29-2021, 05:52 AM.
Leave a comment:
-
Well definitely do not use a Boss DS-1 on this amp, the fuse just went, powered the pedal on and poof blown fuse, worked fine with my VFE Triumvirate I built...
Leave a comment:
-
I did it helped some, but not as much as I’d hoped and they aren’t the easiest kind to get the spray into.
They are almost like alpha...
Leave a comment:
-
-60mv on the output, new resistors in place and J111 reversed, it sounds really nice.
The volume knob seems like it will need replaced in the future,...
- Likes 2
Leave a comment:
-
Go figure once the parts arrive things start happening and I am too busy to mess with the amp.
One day free so far was today and I didn't really feel...
- Likes 1
Leave a comment:
-
Yea it's trippy when you see it like that. XD must have had some backlash over it.
So I need to flip the fet around when I get it apart and replace...
- Likes 1
Leave a comment:
-
So based on the readings it must be installed backwards, I installed it based on it being listed as a GSD, but it appears to be a DSG.
I think when...
Leave a comment:
-
I put it in reverse of the original part because the datasheet, maybe I got a little lucky and the whole datasheet thing doesn't matter as much as I originally...
Leave a comment:
-
I did install it in reverse, but the odd thing is the different datasheets. I did forget to change the 3, but I think I’m being confusing.
...
Leave a comment:
-
This is the datasheet linked on the part that I ordered.
https://www.mouser.com/ProductDetail...vF4DwOPfW9b%2F...
Leave a comment:
-
If I am understanding this correctly then pin 1is drain, pin 2 source, pin 3 is gate?
pin 1 to pin 2 = 98.7k *
pin 2 to pin 3 = 23.3R
...
Leave a comment:
-
Not here, They are trying to force LED fully here... shelves full of LED and only 2 selections of incandescent. I'll have to order online if this bulb fails...
Leave a comment:
-
I'll give it a try in a bit, sorting parts for guitar pedal builds....
Leave a comment:
-
I'll pull it and test it when the resistors arrive, Probably next week, I'm glad this forum exists or I'd be lost....
Leave a comment:
-
I tested for continuity like I was shown in a video, one side was open when bridging the source and gate with the common lead, probe on the other leg, continuity...
Leave a comment:
-
It's cool, mistakes happen and I tend to make a lot of them. Which is why I am trying to make absolutely sure.
The choices I have above,...
- Likes 1
Leave a comment:
-
I knew of the 4k7 etc. from building pedals, but when I read that I don't see 0R27 = .027, I see 0R27 = 0.27.
I have Klein MM700 True RMS it should...Last edited by redkurn; 04-16-2021, 12:56 AM.
Leave a comment:
-
I think you are right, the voltages are off and I can't get a resistance from those two, but I do get voltage and can get a reading of resistance and voltage...Last edited by redkurn; 04-15-2021, 11:38 PM.
Leave a comment:
-
-35.98v
I'm going to take it back a part and see if it changes with the fet out, check and see as Helmholtz suggested.
Maybe the datasheet...
Leave a comment:
Leave a comment: