Results 1 to 5 of 5

Thread: My first pickup wind gone bad

  1. #1
    Twobie
    Join Date
    Jul 2019
    Posts
    2
    Thumbs Up/Down
    Received: 1/0
    Given: 3/0
    Rep Power
    0

    My first pickup wind gone bad

    Hello
    I'm new to the forum.
    Today I wound my first single coil pickup using 42AWG enamel wire. When I checked the ohms, I got no reading. I admit I probably didn't remove the enamel very well on the ends of the wire. Could this be the problem?

    0 Not allowed! Not allowed!

  2. #2
    Supporting Member mozz's Avatar
    Join Date
    Oct 2015
    Location
    NEPA
    Posts
    797
    Thumbs Up/Down
    Received: 173/1
    Given: 120/0
    Rep Power
    4
    Yes, you need to use a fine sandpaper (carefully) before you wrap into the rivets. The solder should flow nice. I do the start rivet soldering before i even wind, because if it breaks when you are done, it will be too short to reach the rivet.

    1 Not allowed! Not allowed!

  3. #3
    Senior Member
    Join Date
    May 2006
    Posts
    3,826
    Thumbs Up/Down
    Received: 178/2
    Given: 17/0
    Rep Power
    18
    I fold over a small piece of fine emery cloth or similar, lightly pinch it around the wire end, and pull the wire through. Alternatively, I'll place the wire end on the surface of a sharpening stone I have and brush the wire with the emery cloth. For me, at least, the trick is being able to hold the wire steady so as to accept the abrasion. The insulation on the wire makes it really slippery, so whatever helps to hold the wire in place is good.

    1 Not allowed! Not allowed!

  4. #4
    Woodgrinder/Pickupwinder copperheadroads's Avatar
    Join Date
    Jun 2009
    Location
    Iceburg Alley ,Newfoundland,CAN
    Posts
    2,136
    Thumbs Up/Down
    Received: 36/0
    Given: 33/0
    Rep Power
    13
    Don't scrap that pickup for the reason you didn't sand the insulation off well enough . it my be a longshot but you can remove the finish from Plain enamel wire with the hot tip from the iron by pushing the against the magnet wire in the eyelet .

    2 Not allowed! Not allowed!
    "UP here in the Canada we shoot things we don't understand"

  5. #5
    Twobie
    Join Date
    Jul 2019
    Posts
    2
    Thumbs Up/Down
    Received: 1/0
    Given: 3/0
    Rep Power
    0
    So I cut off the wire and started again. This time I used 400 grit sandpaper instead of 1000. I could clearly see the exposed wire and now I get a reading and it's right where I want it to be.
    Thanks for the help guys

    1 Not allowed! Not allowed!

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. My first pickup wind (technique help appreciated)
    By cnasc in forum Beginner/ Hobbyist
    Replies: 10
    Last Post: 07-14-2019, 04:15 AM
  2. Help with 1st wind: Split Coil Precision Pickup
    By Lucas in forum Pickup Makers
    Replies: 15
    Last Post: 11-13-2013, 05:23 AM
  3. Pickup Wind Designer program ...what would you like to see included ?
    By Lyrebird Steve in forum Tools and Coil Winding Gear
    Replies: 54
    Last Post: 05-24-2013, 05:02 PM
  4. What is the largest and/or heaviest pickup you wind.
    By enkindler in forum Pickup Makers
    Replies: 13
    Last Post: 08-06-2012, 10:22 PM
  5. Wal-inspired pickup wind
    By Chris Turner in forum Pickup Makers
    Replies: 17
    Last Post: 07-21-2012, 04:46 AM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •