Results 1 to 6 of 6

Thread: PCB manufacture

  1. #1
    Supporting Member
    Join Date
    Dec 2009
    Location
    UK
    Posts
    3,466
    Thumbs Up/Down
    Received: 195/0
    Given: 23/0
    Rep Power
    14

    PCB manufacture

    Someone asked me yesterday about getting low-volume 100mmx70mm double-sided PCBs made and I said I'd look here as I'd seen various recommendations. Except I can't find anything recent. So, for those who are getting PCBs made, who are you using?

    0 Not allowed! Not allowed!
    Last edited by Mick Bailey; 12-02-2019 at 02:12 PM. Reason: typo

  2. #2
    Senior Member
    Join Date
    May 2006
    Location
    Cheshire, UK
    Posts
    2,237
    Thumbs Up/Down
    Received: 542/4
    Given: 288/0
    Rep Power
    16
    I've ordered a few from here - Quick-teck and they were fine.

    0 Not allowed! Not allowed!

  3. #3
    Supporting Member
    Join Date
    Oct 2011
    Location
    Manchester, UK
    Posts
    359
    Thumbs Up/Down
    Received: 30/0
    Given: 27/0
    Rep Power
    9
    I've had stuff from jlcpcb.com and they were dirt cheap. Quality seems fine.

    0 Not allowed! Not allowed!

  4. #4
    Supporting Member
    Join Date
    Aug 2017
    Location
    Portland, OR
    Posts
    713
    Thumbs Up/Down
    Received: 245/1
    Given: 106/2
    Rep Power
    3
    I use the free version of easyeda.com to do my layout and then ordered from them. You don't have to buy from them as you can download gerber files, but it was really easy to order from them and the price was good. I did a batch of two sided stomp box boards, I think I got 30 done for about $30 shipped with a two week turn around. Quality was good, only minor issues is where I made poor choices on component parameters, but I can't fault them for that.

    1 Not allowed! Not allowed!

  5. #5
    Supporting Member
    Join Date
    Dec 2009
    Location
    UK
    Posts
    3,466
    Thumbs Up/Down
    Received: 195/0
    Given: 23/0
    Rep Power
    14
    Nice. I'll send him a link to this thread

    0 Not allowed! Not allowed!

  6. #6
    Supporting Member
    Join Date
    Oct 2011
    Location
    Manchester, UK
    Posts
    359
    Thumbs Up/Down
    Received: 30/0
    Given: 27/0
    Rep Power
    9
    I've been using the easyEDA editor too. It's certainly good enough for my simple tube amp purposes and the learning curve is much less steep than KiCAD.

    1 Not allowed! Not allowed!

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Did SUNN manufacture speakers?
    By Randall in forum SUNN
    Replies: 16
    Last Post: 09-19-2014, 08:03 AM
  2. Vox AC30/TB lookin for a date of manufacture.
    By vernyvern in forum Vintage Amps
    Replies: 3
    Last Post: 11-27-2010, 03:14 PM
  3. Bobbin manufacture
    By rhoads in forum Pickup Makers
    Replies: 30
    Last Post: 12-10-2008, 08:28 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •