Customers can be crazy. Once a customer and friend brought me an amp. He just sits strums and sings, and was using an old Sansui stereo amp for a PA. It was blown up. He was going to need output transistors and other stuff and an hour or more labor. I said, "Jerry, you can just buy another one of these down at the pawn shop for $45, save some money." He said, "Well that is where I bought this one and that is what I paid for it." But he likes it and wanted me to fix it anyway. Oh well.
Announcement
Collapse
No announcement yet.
At what point do you give up on a repair?
Collapse
X
-
There is a psychology in gambling where people will pay a person to guard "their" slot machine while they go to the bathroom. They will also sit for hours at a losing machine because they have got to win eventually, right? Wrong! They have no better odds at one machine or another. The problem is that they have invested $500 worth of quarters in that one machine.
That kind of happens to me. The more I work on an amp, the more I want to repair it because I have invested so much time and effort. It really pains me to give up. When I do I get rid of the amp quickly usually at a loss. I don't keep it around because I don't want that LOSER trophy hanging around reminding me of my failure.
I am trying to keep a positive attitude and reminding myself that I am learning something about the circuit or repair technique even if I did not fix it.
- Likes 3
Comment
-
I can fix anything. I say that, and I believe that. It doesn't always make sense to do so, sure, but I know if there is a solution, I will find it, or invent it. I don't like to give up because I want to solve the puzzle.Education is what you're left with after you have forgotten what you have learned.
- Likes 3
Comment
-
Well ive been playing around with amps for years, Not really an electronics engineer, have had a few dead end jobs where i have learnt some skills
I'm getting busier slowly every year, filling a void in my area where. I use to take on everything and anything, but this has caused me lately to want to stop. I ---- work to live - not live to work
I have stopped doing modern hifi amps , AV amp mostly and any amp that i am wary of i will take a look and if looks like a pile of pain, I had back... Only in 10 yrs have i given back a valve amp un repaired
I have in the past priced a repair up hoping he says no and he says Yes
Keep up the good work and its always a pleasure learning from you guys
- Likes 3
Comment
-
I just gave up on a repair this morning. Aguilar Tone Hammer. The complaint was the Midrange Frequency Pot wasn't working. Verified that in closed-box checkout, so proceeded to attempt removing the top cover. Tiny Philips #1-size FH SMS's used. Got all but two screws to break their bond and unscrew...last pair would have stripped out the Philips pattern. Resorted to using Freeze mist to freeze the screw head, and was able to break the bond and not the screw, finally getting the cover off. The front panel PCB....loaded with SMD parts and thru-hole panel pots soldered into both sides of the double sided board, along with switches and LED's.
Getting the board out required backing out the screws holding the shield wall between that board and the combined SMPS/Class D PCB assembly. Got the board out, took a bit of time unsoldering the Lead-Free solder joints of the dual gang Freq Tuning pot. Finally got all six leads to wiggle, having removed all but the solder within the plate-thru holes clinging to the leads, and removed the pot. Applied contact cleaner to both resistance wafers, and verified both elements work. Put the pot back in, reassembled the unit (PITA), and put the cover back on with just a few screws attached. No change...Freq Pot still not working. Pulled the top cover off again, verified the top side of the PCB's pot terminal traces wandered into the cluster of SMD caps and resistors, nothing broken on the top side traces. No documents, and too small to want to spend any more time. Put the cover back on, returned it to the Guitar Dept to send back to Aguilar back east. I should have stopped before even pulling it apart, but wanted to at least say I tried.Logic is an organized way of going wrong with confidence
- Likes 2
Comment
-
Bing Bing Bing....hidden nugget alert.....
Resorted to using Freeze mist to freeze the screw head, and was able to break the bond and not the screw, finally getting the cover off.
Cool trick
nosajsoldering stuff that's broken, breaking stuff that works, Yeah!
- Likes 4
Comment
-
I think when you get to the point where the actual board can be defective, those kinds of equipment I tend to quickly 'skim' for simple faults and then give them a pass if it's not something simple. Like double sided with lots of via's, or triple layer, or even the bad run of Marshall TSL boards. People do the TSL's now because someone went to a lot of trouble to discover the faults and there are known work-arounds. Otherwise it would not be economically feasible.
I'm thinking particularly of stuff like line 6 where they used to want you to do board swaps because they knew an internal fault of the actual pcb was possible.
Aside from that I'm with those here who see the real tough ones as a form of education.
And nothing more satisfying than finding the fault on something that has done the rounds to several reputable shops and no one else was able to fix it.
Originally posted by EnzoI have a sign in my shop that says, "Never think up reasons not to check something."
- Likes 6
Comment
-
I was working on an amp today that I refer to as Schroedinger's Crate. It is a GT80 DSP that would lose most of its signal after it warmed up, but if you sat on the cabinet or touched a push button or something it would be OK for a second. Get it opened up and am chopsticking around looking for a cold solder joint and anywhere you tap would send it in or out of the fault state. Touch a wire harness? Changes state. Probe a pin? Changes state. Finally pulled the board and reflowed pins on the tube closest to the output section. Seems like it might be stable now. This amp really isn't worth the hassle of multiple tear-downs, but I really hate junking stuff that can be fixed. I figure if I spend enough time poking at it I will get it eventually.
Comment
-
Whenever I have a Crate on the bench, I go through ALL the jacks. They use the Cliff style jacks. And most have cutout contacts, so I carefully measure the RESISTANCE between the cutout contacts. If it is more than HALF an ohm, I consider it a problem. Two ohms sounds good, after all what can 2 ohms interfere with? But it SHOULD have close to zero ohms, and the fact it sits there at 2 ohms tells us the contacts are not pristine, and can just as easily go higher from time to time. This solves the complaint of a Crate dropping output level now and then, and the FS jack causing unwanted random channel switching, all by itself.Education is what you're left with after you have forgotten what you have learned.
- Likes 4
Comment
-
My basic rule of thumb is that if the repair exceeds 50% of the replacement cost then it's not economical unless the customer has a very special reason to spend whatever is needed to fix it. I usually take a look just to be certain the fix isn't going to be dead simple and I may be missing something. How many hours can you put into fixing a looper pedal that cost $25?
Sometimes though the reward is tantalizingly just out of reach and I recently put an absurd amount of time into trying to fix an Ernie Ball/Music Man Majesty guitar. And as a friend used to tell me, "If you're trying, you're not doing". I could see exactly what was happening but the problem is the factory only replaces boards and couldn't offer any in-depth technical help. I gave up on that one because the boards were only available to me at full retail and the cost was too high for me to want to guarantee the parts.
- Likes 1
Comment
-
Originally posted by Mick Bailey View Postas a friend used to tell me, "If you're trying, you're not doing".
It's one of my not-so-favorite wastes of time, flogging a piece of gear until it's hopeless. But I do it anyway. Sometimes a crustomer loses patience & takes it away. In other cases the customer has an awful lot of patience. For instance I had a recalcitrant powered subwoofer that would not yield. It sat around here for over 3 years, hogging half a cubic yard of my space. When the customer eventually signaled he wanted to pick it up no matter what, I gave it one last attempt. And this time, I won! Turned out to be something easy simple & cheap. I had overlooked those options the first couple times around. He was delighted. And now he's serenading his neighbors with boom boom bump-diddy-ump.
This isn't the future I signed up for.
- Likes 2
Comment
-
I have a Trace Elliot bass head that I am going to have to give up on and it really ticks me off. I bought it as a fixer, found the Bipolar Bear power amp module was totally fried. It was not the first time it had burned up, so many traces were obliterated, etc. I found a class D amp module that was a great fit for it, so I wait 6 weeks or whatever for it to come from China. I installed it and it worked well at first, but there was some preamp hum. As I get ready to start diagnosing that it starts popping fuses. It looks like the PT must have developed an internal short (bright LBL with secondaries disconnected), maybe it is only after it is warmed up or something, but basically that puts this into the not worth fixing file.Last edited by glebert; 11-17-2020, 10:49 PM.
Comment
-
Originally posted by Enzo View PostWhenever I have a Crate on the bench, I go through ALL the jacks. They use the Cliff style jacks. And most have cutout contacts, so I carefully measure the RESISTANCE between the cutout contacts. If it is more than HALF an ohm, I consider it a problem. Two ohms sounds good, after all what can 2 ohms interfere with? But it SHOULD have close to zero ohms, and the fact it sits there at 2 ohms tells us the contacts are not pristine, and can just as easily go higher from time to time. This solves the complaint of a Crate dropping output level now and then, and the FS jack causing unwanted random channel switching, all by itself.
And yea, it REALLY sucks when something just bites you in the a*s and won't cooperate. A lot of the time, I'll still try to figure out whats wrong and repair it, because if you learn something from it, then you didn't waste your time!1937 Gibson L50 "Black Special #4"
1978 Gibson Melody Maker D Reissue
2004 Ibanez SZ720FM
Epi SG '61 with 490R & 498T Pickups
Couple Marshalls, Crate Blue VooDoo
Couple 4x12 cabs
Couple Orange combos
TONS OF FREAKING TEST GEAR- SCOPES, METERS ,ANALYZERS
SIG GENS, ETC, ETC, ETC.
Comment
Unconfigured Ad Widget
Collapse
Comment