Announcement
Collapse
No announcement yet.
Search Result
Collapse
49 results in 0.0052 seconds.
Keywords
Members
Tags
-
No, unfortunately there are no tags or numbers.
-
Trace Elliot GP12 250 Toroidal Transformer
Does anyone know where I can get a toroidal transformer for a Trace Elliot GP12 250 bass amp? I have put requests into British Audio which supposedly has...
-
Marshall SL5 Clean Channel Issues
Have a Marshall SL5 that has no sound coming through the clean channel. The OD channel works fine. Traced the problem to the 11-pin wiring harness and connectors...
-
Thanks Dude. This is actually a Bassist 1, not a 2. I didn't even notice it as the owner said it was a 2. That is why the pictures above don't match. I will...
Leave a comment:
-
I am thinking 60Hz but I always get them confused. It is the same hum as when you touch the tip of your guitar cord plug when it is plugged into an amp.
Leave a comment:
-
The hum is coming out of the speakers. Filter caps look good but it probably won't hurt to change them out, a lot less expensive than a new PT. What else...
Leave a comment:
-
They both said Bassist 2 on the fronts. Maybe the other one is a newer version? As far at the PT, the owner wanted the PT swapped out in order to eliminate...
Leave a comment:
-
Here are a couple of pictures of the actual amp I am working on. The above photo was off of an ad on E-bay. Looks like it has been modded - PT etc.
...
Leave a comment:
-
DeArmond Bassist 2
I have a DeArmond Bassist 2 bass guitar combo with a blown power transformer. There is very limited information out there on the web and was wondering if...Last edited by DPM309; 06-26-2017, 04:32 PM.
-
Cleaned the foot switch jack and checked R170 which read 10 Ohms and chop-sticked all of the cable connections inside the amp with no luck. Still need to...
Leave a comment:
-
It is now unplugged. In fact I don't have it in my possession at this time. I am now using the channel selection switch on the front. Clean channel sounds...
Leave a comment:
-
TC, both plate resistors for V2 (R101 - 150K and R102 - 100K) checked out. I am getting 155 VDC on Pin 1 and 259 VDC on Pin 6. I did check your thread out...
Leave a comment:
-
Peavey VK 112 Weak Lead Channel
I have a Peavey Valveking VK112 with very weak and distorted volume on the Lead Channel. The Clean channel works just fine. Tubes all tested good and even...
-
Thanks for the reply. Unfortunately the owner wants an exact replacement from Blackstar which will probably not be possible unless I can get it overnighted....
Leave a comment:
-
Blackstar Artisan 100 OT
I am looking for an output transformer for a Blackstar Artisan 100. Can't find anything on their website and was wondering if a Marshall 100 Watt OT would...
-
The amp does make some noise when I switch channel so I will go ahead and replace both Q1 and 4. The reverb is working fine but I will replace Q4 as long...
Leave a comment:
-
Enzo,
Thanks for the quick response and advice. Sorry for the confusion on the model of the amp. Also, I should have seen the 1 meg resistor...
Leave a comment:
-
Peavey 6505 (5150) Distortion
I am working on a Peavey 6505 (5150) that is experiencing low volume and distortion. The pre pots do change the volume level somewhat but the post pots do...
-
Thanks for all of the suggestions. I will let you know what I find when I get the amp later this week.
Dan
Leave a comment:
-
Polytone Mini Brute IV
I will be getting a Polytone MB IV to work on that has an issue with crackling/static noise after the amp has been running for a couple of hours. Read all...
-
Thanks for the tip. Turns out the owner did not want to spend the money at this time but I will keep this for future refenence.
Leave a comment:
Leave a comment: