Announcement
Collapse
No announcement yet.
Search Result
Collapse
500 results in 0.2819 seconds.
Keywords
Members
Tags
-
I use a CO2 laser to cut P90's, both to top and bottom flatwork and the 1/4" spacer. Works great. Don't know anything about diode lasers, but if they...
-
I tension with a pair of heavy felt pieces sandwiched between two pieces of metal with a thumbscrew to loosen or tighten that the wire passes through before...
Leave a comment:
-
I also use clam shell style bobbin assembly jigs with guide pins and a top section that presses the top flatwork on. The assembling itself is done on a 1...
- Likes 2
Leave a comment:
-
Try using less tension on the wire during the wind. I had similar issues when I first started winding, I reduced the tension and the flared bobbins disappeared....
Leave a comment:
-
Similar to what you are using, I use a variac to control the voltage to my wax pot, a small cheap crock pot. I know where I need to set it to achieve the...
Leave a comment:
-
It doesn't matter which end of the spool the wire comes off of. However, sometimes you may find that one end has some rough areas on the lip of the plastic...
- Likes 1
Leave a comment:
-
The wire I just removed from the '83 4003 bridge mic'd out at .0021", so I'm calling it AWG 44 (min). Definitely Formvar based on the colour. As previously...Last edited by kayakerca; 02-21-2022, 03:21 AM.
- Likes 1
Leave a comment:
-
I was thinking about bumping up the output to that +/- 9K range as well for a tad more umph. Thanks for the Ricky forum link. ...
Leave a comment:
-
Any chance you took a DCR reading on the neck? Interested in the spread....
Leave a comment:
-
-
Rickenbacker Bass Treble Pickup Spec's
I have an '83 Rickenbacker Treble Pick up coming in for a rewind and am having trouble finding any info on the internet wrt the DCR of that bridge pickup....Last edited by kayakerca; 02-12-2022, 10:30 PM.
-
Don't know what "ISO" stands for wrt pickup bobbins, but. . .
https://www.wdmusic.com/wd-slug-bobb...52mm-spacing-d...
Leave a comment:
-
I haven't bought any for a couple years, but is was ~ 7.50/lb for 0.093" (~ $6.50/lb for 0.062) at EPSE. If I remember correctly, for a Strat p/u that...
Leave a comment:
-
I use the technique Jason Lollar posted a while back. Put some Windex in a sealable container, place your laser cut flatwork in it, put the lid on the container,...Last edited by kayakerca; 08-20-2021, 01:00 AM.
- Likes 1
Leave a comment:
-
When I get back from (retired person) vacation, I have an early 60's 8 string Fender 400 (jazzmaster style) steel guitar pickup to rewind. This is a new...
- Likes 1
Leave a comment:
-
I don't wind hand guided, but the speed that gives me reproducible results is 1,131 rpm. That and a dynamometer to set the tension before each wind gets...
- Likes 1
Leave a comment:
-
-
I have found that my Strat winds are close to 1kΩ hotter right after the wind is finished and the leads are soldered on. I always attributed it to...
- Likes 1
Leave a comment:
-
-
You might want to look on ebay for a commercial grade linear actuator like this. A 1" stroke for $35.
https://www.ebay.com/itm/Haydon-K...Last edited by kayakerca; 12-21-2020, 08:08 PM.
Leave a comment:
-
Followup. . . . .
After being unable to reach Tone Kraft, I went to the PayPal resolution center. After they attempted to contact TK 7 times,...
Leave a comment:
Leave a comment: